Gefen EXT-UHD-CAT5-ELRPOL User Manual Page 1

EXT-UHD-CAT5-ELRPOLUser Manual*PreferredRelease A14K Ultra HD ELR-POL Extender w/ RS-232, Ethernet and 2-way IR

4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet and 2-way IR1 Getting StartedIntroduction...

page | 2IntroductionSender UnitLink EthernetIR In/ExtIR OutEXT-UHD-CAT5-ELRPOLSPowerLink24V DCHDMI InRS-232ELR-POL Extender S4K Ultra HDw/ RS-232, Eth

page | 3IntroductionID Name Description1 Link Connect a CAT-5e cable (or better), up to 495 feet (150 meters), from this port to the Link port on the

page | 4IntroductionReceiver UnitLink EthernetIR In/ExtIR OutEXT-UHD-CAT5-ELRPOLRPowerLink24V DCHDMI OutRS-232ELR-POL Extender R4K Ultra HDw/ RS-232,

page | 5IntroductionID Name Description1 Link Connect a CAT-5e cable (or better), up to 495 feet (150 meters), from this port to the Link port on the

page | 6InstallationConnection Instructions ► Video1. Connect the included HDMI cable between the Ultra Hi-Def source and the HDMI In port on the Sen

page | 7Sample Wiring DiagramInstallationCAT-5 CABLE HDMI CABLERS-232 CABLEIR INIR EmitterRS-232 Controlled DeviceIR EmitterGigabit SwitchUltra HD Dis

page | 94K Ultra HD ELR-POL Extender w/ RS-232, Ethernet and 2-way IR2 Basic OperationLED Status ...

ii1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this product near water.6.

page | 10LED StatusBasic OperationBasic OperationThe Power Link LED indicator on the Sender and Receiver unit provides basic information on the curren

Controlling the Source from the Viewing Location1. Connect the included IR extender to the IR In/Ext port on the Receiver unit. If using an automati

Controlling the Display from the Source Location1. Connect the included IR extender to the IR In/Ext port on the Sender unit. If using an automatio

Controlling the Source / Display from Different Locations Using bidirectional IR, the 4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet, and 2-wa

page | 14DIP Switch CongurationOn the bottom of both the Sender and Receiver unit are a set of DIP switches. The Sender unit has a bank of four DIP

page | 15DIP Switch CongurationEach of the following sections describe the DIP switch settings that control each feature. DIP switches that are not

page | 16DIP Switch CongurationHDCP ModeSome source devices (e.g. computers) will always send HDCP. This may cause problems in some systems. Set DI

page | 17DIP Switch CongurationHDBT (HDBaseT™) Mode1080p Full HD can be extended up to 495 feet (150 meters) and is limited to 8-bit color depth. 4K

4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet and 2-way IR3 Advanced OperationRS-232 Setup ...

iiiGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects and Gef

page | 20RS-232 SetupAdvanced OperationConnecting RS-232 DevicesThe 4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet, and 2-way IR supports RS-232 pas

page | 21Command Description#fw_upgradeUsed to upgrade the rmware#hdcpEnables / disables HDCP detection#helpDisplays a list of available RS-232 comma

page | 22CommandsAdvanced Operation.#hdcpEnables / disables HDCP detection on the input. Some computers will enable HDCP if an HDCP-compliant display

page | 23Commands#helpThe #help command displays the list of available RS-232 commands. Help on a specic command can be displayed when using param1.

page | 24Commands#power_alwaysSets the power mode. The unit must be rebooted after changing the power mode.Syntax#power_always param1Parametersparam1

4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet and 2-way IR4 AppendixUpdating the Firmware ...

page | 28There are two methods for updating the 4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet, and 2-way IR. The recommended method is to update b

page | 29Updating the Firmware7. Assign the following serial port settings in Hyperterminal: Description SettingBaud rate19200Data bits8ParityNoneS

ivTechnical Support(818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday, Pacic TimeFax(818) [email protected]://www.

page | 30Individual Update ProcedureThis method requires that the Sender and Receiver unit are updated separately. Unless there is a specic reason, t

page | 317. Assign the following serial port settings in Hyperterminal: Description SettingBaud rate19200Data bits8ParityNoneStop bits1Hardware ow

page | 32The Sender and Receiver units can be mounted on any at surface, as shown below (screws not included). There should be an inch or two of cle

page | 33Network Cable DiagramFront of RJ-45 ConnectorGefen recommends the TIA/EIA-568-B wiring option. Use the following table when terminating cable

page | 34Supported FormatsVideo • 4K x 2K• 1920 x 1200 (WUXGA)• 1080p Full HDAudio • Linear PCM (7.1 channels)• Dolby® TrueHD• DTS-HD Master Aud

page | 35IndexAppendixSymbols#fw_upgrade 21#hdcp 22#help 23#power_always 24BBidirectional IR Control 11CCommands 21#fw_upgrade 21#hdcp 22#help

20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] it. Switch it. S

vvUltra Operating Notes• Gefen recommends using CAT-5e (or better) cables.• Resolution will affect extension distance. 1080p Full HD can be extende

viFeatures• Extends 4K Ultra HD (3840 x 2160 @ 30 Hz), Ethernet, RS-232, and Bi-Directional IR over a single CAT-5e cable up to 330 feet/100 mete

viiPacking ListThe following items are shipped with the 4K Ultra HD ELR-POL Extender w/ RS-232, Ethernet, and 2-way IR. If any of these items are not

viiiTable of Contents1 Getting StartedIntroduction.......