Audio Embedder 3GSDI EXT-IP-2-RS2322User ManualIP to RS-232 Converter*PreferredRelease A1
IP to RS-232 Converter1 Getting StartedIntroduction...
page | 2IntroductionRS-232 1 PowerIP ResetEXT-IP-2-RS2322Gefen5V DC IP control RS-232 2IP to 2xRS-232ConverterRS-232 1 PowerIP ResetEXT-IP-2-RS2322Gef
page | 3IntroductionID Name Description1 IP Reset Resets the unit to its default IP settings.2 RS-232 1 Connect an RS-232 cable from this port to an R
page | 4InstallationGetting StartedConnection Instructions1. Connect an Ethernet cable between the IP-based control device and the IP control port on
page | 7IP to RS-232 Converter2 Advanced OperationRS-232 and IP Conguration ...
page | 8RS-232 and IP CongurationAdvanced OperationAdvanced OperationConfiguration using the Gefen Discovery ToolWhen using the IP to 2 x RS-232 Conv
page | 9Advanced OperationConfiguration using RS-232To congure the IP settings of the IP to 2 x RS-232 Converter using RS-232 commands, use the follo
ii1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this product near water.6.
page | 10RS-232 and IP CongurationAdvanced OperationAdvanced Operation5. Set the gateway (router) IP address using the #set_gateway command.6. Set
page | 11Advanced OperationCommand Description#helpDisplays a list of all available commands#set_add_delimEnables or disables option to add delimiter
page | 12Advanced OperationAdvanced OperationCommandsCommand Description#show_serial_paramsDisplays the settings of the specied RS-232 port#show_teln
page | 13Advanced OperationCommands#helpDisplays help on a specic command. If no command is specied (param1), then a list of all available commands
page | 14CommandsAdvanced OperationAdvanced Operation#help #show_ipcong#set_ipadd#set_netmask#set_gateway#set_http_port#set_tcp_term_port#set_udp_por
page | 15CommandsAdvanced Operation#set_add_delimEnables or disables the option to include a delimiter as part of the data sent to the control system.
page | 16CommandsAdvanced OperationAdvanced Operation#set_device_descrSets the device description. The device description cannot exceed 30 characters
page | 17CommandsAdvanced Operation#set_end_delSets the end-delimiter mode and value for the specied serial port. The End Delimiter value must be spe
page | 18Commands#set_gatewaySets the gateway address. The gateway must be typed using dot-decimal notation. The matrix must be rebooted after exec
page | 19Commands#set_http_portSpecies the Web server listening port. The unit must be rebooted after executing this command. The default port sett
iiiGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects and Gef
page | 20Commands#set_ipaddSpecies the IP address of the IP to 2 x RS-232 Converter. The IP address must be specied using dot-decimal notation. Th
page | 21Commands#set_netmaskSets the subnet mask. The subnet mask must be entered using dot-decimal notation. The unit must be rebooted after execut
page | 22Commands#set_send_byte_cntSets the send-byte count value for bridging mode.Syntax#set_send_byte_cnt param1Parametersparam1 Serial port
page | 23Commands#set_send_time_outSets the time-out value for sending data collected from a device to the control system in Bridging Mode when a Star
page | 24Commands#set_serial_descrAssigns a descriptor to the specied serial port. The serial port description cannot exceed 20 characters in length.
page | 25Commands#set_serial_modeSets the mode of the specied serial port. The default mode for all serial ports (1 - 2) is TCP Bridge mode.Syntax#s
page | 26CommandsAdvanced OperationAdvanced Operation#set_serial_paramsAssigns the settings to the specied serial port.Syntax#set_serial_params param
page | 27CommandsAdvanced OperationExample#set_serial_params 1 8 1 N 19200 1000 Serial port 1 parameters: Word length = 8 bits Stop bits = 1 bit Pa
page | 28CommandsAdvanced OperationAdvanced Operation#set_start_delSets the Start Delimiter mode and value for the specied serial port. The Start Del
page | 29CommandsAdvanced Operation#set_tcp_br_portSets the TCP bridge listening port for the specied serial port. The default port settings for RS-2
ivTechnical Support(818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday, Pacic TimeFax(818) [email protected]://www.
page | 30CommandsAdvanced OperationAdvanced Operation#set_tcp_term_portSets the TCP terminal listening port. The default port settings is 23.Syntax#s
page | 31CommandsAdvanced Operation#set_telnet_passSets the TCP Terminal password. The password cannot exceed 20 characters in length. param3 is use
page | 32CommandsAdvanced OperationAdvanced Operation#set_udp_br_portSets the UDP bridge listening port. The default UDP bridge port settings for RS-2
page | 33CommandsAdvanced Operation#set_udp_echo_brEnables or disables UDP bridge echo.Syntax#set_udp_echo_br param1 param2Parametersparam1 Serial
page | 34CommandsAdvanced OperationAdvanced Operation#set_udp_portSets the UDP server listening portSyntax#set_udp_port param1Parametersparam1 Ser
page | 35CommandsAdvanced Operation#set_udp_remote_brAssigns the UDP Bridge settings for the specied serial port. param2 must be entered in dot-deci
page | 36CommandsAdvanced OperationAdvanced Operation#set_udp_ripSets the remote UDP IP address. The IP address must be entered using dot-decimal not
page | 37CommandsAdvanced Operation#set_udp_rportSets the remote UDP listening port. The default port settings is 50008.Syntax#set_udp_rport param1Pa
page | 38CommandsAdvanced OperationAdvanced Operation#show_del_prmsDisplays the current delimiter parameters for the specied serial port.Syntax#show_
page | 39CommandsAdvanced Operation#show_device_descrDisplays the device description.Syntax#show_device_descrParametersNoneExample#show_device_descr D
vvOperating Notes• When using the IP to 2 x RS-232 Converter for the rst time, it is recommended that the unit be congured using the Gefen Discover
page | 40CommandsAdvanced OperationAdvanced Operation#show_ipcongDisplays the current TCP/IP and UDP settings.Syntax#show_ipcongParametersNoneExampl
page | 41CommandsAdvanced Operation#show_meEnables or disables the ashing of the LED on the device. When enabled, the LED indicator will ash red and
page | 42CommandsAdvanced OperationAdvanced Operation#show_serial_descrDisplays the description of the specied serial port.Syntax#show_serial_descr p
page | 43CommandsAdvanced Operation#show_serial_modeDisplays the mode of the specied serial port.Syntax#show_serial_mode param1Parametersparam1 P
page | 44CommandsAdvanced OperationAdvanced Operation#show_serial_paramsDisplays the current settings of the specied serial port.Syntax#show_serial_p
page | 45CommandsAdvanced Operation#show_telnet_passDisplays the current TCP terminal password.Syntax#show_telnet_passParametersNoneExample#show_telne
page | 46CommandsAdvanced OperationAdvanced Operation#show_ver_dataDisplays the current software and hardware version.Syntax#show_ver_dataParametersNo
page | 47CommandsAdvanced Operation#system_wide_resetRestarts the IP to 2 x RS-232 Converter according to the supplied parameter.Syntax#system_wide_re
page | 48CommandsAdvanced OperationAdvanced Operation#use_discoveryEnables or disables discovery access mode. If this mode is disabled, then theIP to
page | 49CommandsAdvanced Operation#use_tcp_accessEnables or disables TCP access mode. This mode must be enabled before using RS-232 command to congu
viFeatures and Packing ListFeatures• Allows IP control of two RS-232-enabled devices• Supports Telnet and UDP protocols• Each of the RS-232 devices
page | 50CommandsAdvanced OperationAdvanced Operation#use_tcp_term_passEnables or disables the use of the password during terminal sessions.Syntax#use
page | 51CommandsAdvanced Operation#use_udp_accessEnables or disables UDP access.Syntax#use_udp_access param1Parametersparam1 Value [0 ... 1]Va
page | 52#use_udp_echoEnables or disables UDP echo.Syntax#use_udp_echo param1Parametersparam1 Value [0 ... 1]Value Description0Disable UDP echo
page | 53Advanced OperationWeb InterfaceUsing the built-in Web InterfaceAccess the built-in Web interface by entering the IP address of the IP to 2 x
page | 54Web InterfaceRS-232Select RS-232 Port Select the RS-232 port from the drop-down list.Options: 1, 2 Description Enter a description for the de
page | 55Web InterfaceBaud Rate Select the baud rate used by the RS-232 device from this drop-down list.Options: 110, 300, 600, 1200, 2400, 4800, 9600
page | 56Web InterfaceLine Delay (ms) Enter the line delay in this eld.Range: 0 ... 10000 Force Send (ms) If no data is received from the controlle
page | 57Web InterfaceAdd Delimiters to data sent Include the delimiter characters in the data sent to the control system. Check the Add box to enabl
page | 58Web InterfaceEnd Delimiter Value This value can be up to three ASCII characters (3 bytes), in length. The value must be entered in hexadecim
page | 59Web InterfaceDestination IP Enter the destination (where the data will be sent) IP address in this eld.Range (per byte): 0 ... 255 Destinati
vii
page | 60Web InterfaceNetwork tabMAC Address The MAC address of the IP to RS-232 Converter. The MAC address cannot be changed. Mode Select the netw
page | 61Web InterfaceGateway The gateway (router) IP address to with the IP to 2 x RS-232 Converter is connected.Range (per byte): 0 ... 255 HTTP P
page | 62Web InterfaceEnable TCP Access Enables or disables TCP access. Options: Enable (checked), Disable (unckecked) Require Password on Connect
page | 63Web InterfaceNew Password Type the new password in this eld. The password is automatically masked when entered. The password is case-sensi
page | 64Web InterfaceEnable UDP Access Enables or disables UDP access. Options: Enable (checked), Disable (unckecked) UDP Port Sets the UDP port.R
page | 65Web InterfaceDestination UDP IP Address Enter the remote UDP IP address in this eld.Range (per byte): 0 ... 255 Destination UDP Port Type th
page | 66Web InterfaceAdvanced OperationAdvanced OperationSystem tabDownload (Download Current Conguration) Saves the current conguration of the IP
page | 67Web InterfaceAdvanced OperationBrowse... (Firmware Update) Click this button to select the rmware le to be uploaded. Update Click this butt
IP to RS-232 Converter3 AppendixDefault Settings ... 7
viiiTable of Contents1 Getting StartedIntroduction...
page | 70Default SettingsAppendixAppendixThe following table lists the default setting of the IP to 2 x RS-232 Converter, as displayed under the built
page | 71AppendixNetworkIP SettingsMAC Address • Device-dependent (cannot be changed)Mode • StaticIP Address • 192.168.1.72Subnet • 255.255.255.0G
page | 72AppendixConnectors, Indicators, and ControlsRS-232 • 2 x DB-9, maleIP control • 1 x RJ-45Power • 1 x 5V DC, lockingPower indicator • 1 x
20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] it. Switch it. S
Comments to this Manuals