Gefen GTV-ETH-2COAX User Manual

Ethernet Over CoaxUser Manualwww.gefentv.comGTV-ETH-2-COAX

7RECEIVER PANEL DESCRIPTIONSStandby Button1. Pressing this will put the receiving unit in standby mode. The unit will not transfer any information to

8How to Connect the GefenTV Ethernet Over CoaxInstallation of the GefenTV Confi guration AssistantInsert the included installation CD-ROM into your com

9GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATIONClose all other applications and press the Next button to continue.5. Please read the license agreeme

10Please choose the program installation destination. The default location 7. is “C:\ Program Files\Gefen TV Ethernet Over Coax”. To set your own dest

11Connect the source (i.e. computer, router, switch) to the GefenTV Ethernet 1. Over Coax sender unit using the supplied CAT-5e cable.Connect the Gefe

12CONFIGURING THE GEFENTV ETHERNET OVER COAXOnce both the sending and receiving units are linked and powered, basic confi guration can proceed. This se

13CONFIGURING THE GEFENTV ETHERNET OVER COAXOnce all possible nodes have been detected, the program will display all of 6. these nodes as in the windo

14CONFIGURING THE GEFENTV ETHERNET OVER COAX8. The PLC node confi guration screen is separated into the following items:NET IDThis is the name of the n

15CONFIGURING THE GEFENTV ETHERNET OVER COAXOnce the update is complete, a message will appear to indicate the update 9. was successful. Click on the

16CONFIGURING THE GEFENTV ETHERNET OVER COAXOnce the confi guration for the remote node is complete, the local node will 11. then have to be confi gured

Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monday thru Friday.Write T

17AUTOMATIC SECURITY CONFIGURATION FEATURETo quickly setup the Gefen TV Ethernet Over Coaxial for secure use, the Automatic Security Confi guration Mod

18AUTOMATIC SECURITY CONFIGURATIONConnect the computer with the installed Gefen TV software to the node you 1. wish to set as the Master node. Press a

19ADVANCED CONFIGURATIONThere are optional advanced settings that can be confi gured for each node. The advanced menu can be accessed directly through

20ADVANCED CONFIGURATIONFirmware UpdateThis section is used to update the node’s fi rmware from a server location. Please see the Firmware Update secti

21ADVANCED CONFIGURATIONMULTICASTIGMP MulticastThis option will enable or disable the node’s ability to transmit IGMP multicast data.SECURITYThe secur

22ADVANCED CONFIGURATIONVLANThis option will enable or disable the node’s ability to accept VLAN data. If this feature is enabled on one of the nodes,

23ADVANCED CONFIGURATIONADAVANCED QOSQOS (quality of service) prioritization. Rule 1 will be applied to all packets fi rst and then Rule 2. Prioritizat

24WEB CONFIGURATIONIf an IP address has been set in the ADVANCE CONFIGURATION PANEL, access to the WEB UTILITY will be enabled. To access the WEB UTIL

25WEB CONFIGURATIONMAIN PAGEThe main page will display general confi guration information. Clicking on the further information link will navigate to a

26WEB CONFIGURATIONThe confi guration options are as follows:MAC Confi gurationNetwork Confi gurationMulticast Confi gurationVLAN Confi gurationPriority Co

CONTENTS1 Introduction2 Operation Notes3 Features4 Sender Panel Layout5 Sender Panel Descriptions6 Receiver Panel Layout7 Receiver Panel Descripti

27FIRMWARE UPDATE PROCEDUREThe fi rmware for the GefenTV Ethernet Over Coax can be updated by FTP, TFTP, or a direct fi le. The fi rmware update can be e

28Standard Support ... UPA DHS (200 Mbps) PLCInterface ... One Power Line port / One coaxial

Congratulations on your purchase of the GefenTV Ethernet Over Coax. Your complete satisfaction is very important to us.Gefen TVGefen TV is a unique pr

READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFENTV ETHERNET OVER COAXThis device passes all 10/100BASE-T Ethernet network protocols (TCP/• IP,

3FeaturesSupports up to 200 Mbps data transmission rate• Extension of up to 1000 feet (300 meters)• Web confi guration for easy maintenance• Features i

4Front PanelBack PanelTop PanelBack Panel14253Top Panelp678SENDER PANEL LAYOUT

5SENDER PANEL DESCRIPTIONSStandby Button1. Pressing this will put the sending unit in standby mode. The unit will not transfer any information to the

6Front PanelBack PanelTop Panel14253Top Panelp67891011RECEIVER PANEL LAYOUT